Ti3C2纳米层状材料对废水中Cr（Ⅵ）的光催化去除性能

以Ti₃AlC₂为原料,采用HF刻蚀工艺制备出12种Ti₃C₂纳米层状材料,对其形貌进行了表征,并考察了以其作为光催化剂对废水中Cr（Ⅵ）的处理效果。实验结果表明：HF体积分数为80%、刻蚀时间为48 h时得到的MX-80-48的形貌较好;MX-80-48具有类似石墨烯的二维层状结构,纳米层厚度约20~50 nm,孔径2~10 nm,比表面积14.8 m²/g,在400~700 nm可见光范围内表现出强烈的吸光性;当Cr（Ⅵ）的初始质量浓度为40.00 mg/L、MX-80-48投加量为200 mg/L、pH=2、反应时间4 h（暗反应1 h+光照3 h）时,Cr（Ⅵ）去除率可达100%。     

Challenges for modelling and integrating environmental performances in concept design: the case of an automotive component lightweighting

The objective of this paper is to discuss the main barriers for modelling and integrating the environmental performances in the automotive concept design. Incorporating environmental assessment in the early design phase of a vehicle component is known as an important challenge that car makers need to face in order to develop more sustainable design solutions; in this regard, the Life Cycle Assessment is the most widespread methodology for the environmental assessment and comparison of alternatives. The present work illustrates the combination of such methodology with the traditional design procedure at two different levels of the component design phase, material choice and concept design. In particular, the potential benefits originated by a lightweight solution for the automotive component Throttle Body are evaluated by considering environmental and technical implications at the same level. The case study shows that a multi-disciplinary approach for design effectively allows the integration of the environmental issue in the company’s established procedures. However, interpretation of results is still a challenging aspect due to the inevitable contradicting elements which should not discourage to develop comprehensive sustainability assessment within the early design stage.     

Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.     

垃圾焚烧烟气中HCl与消石灰的反应机理研究

测试了两种消石灰与垃圾焚烧烟气中HCl的反应率,得出了消石灰的反应率与反应时间的反应曲线,分析了消石灰与HCl的反应机理及影响消石灰最终反应率的因素。试验结果表明,消石灰与HCl反应初期按灰层扩散控制进行,两种消石灰的最终反应率分别为16％和36％。     

上海地区大气中氯化氢和颗粒氯排放源清单初步研究

氯自由基对于臭氧和二次气溶胶的生成贡献不容忽视.夜间颗粒相氯(Cl~-)可以通过与N_2O_5的复杂反应转化生成ClNO_2,其光解产生的氯自由基将显著影响大气污染的形成机制.本文以上海地区为案例,以2017年为基准年,收集了人为源活动水平数据,采用排放系数估算方法,首次建立了上海地区人为源氯化氢(HCl)和颗粒氯(Cl~-)的排放清单;并进一步结合模型计算海盐气溶胶排放的颗粒氯(Cl~-).结果表明,2017年上海市人为源和天然源排放的HCl和Cl~-分别为1207 t和820 t,其中,燃煤、工业、垃圾焚烧和秸秆燃烧产生的HCl排放量分别为327、134、722和24 t.燃煤源中的燃煤电厂和其它行业燃烧约占燃煤源排放的80%;工业源中水泥为HCl的最大排放源,约占工业源排放的51%;垃圾焚烧厂排放约占总HCl排放的60%,为最大的HCl排放源.燃煤、工业源、垃圾焚烧、秸秆焚烧、烹饪源和海盐的颗粒Cl~-排放量分别为82、153、498、47、39和0.6 t,燃煤源中的燃煤电厂占燃煤Cl~-排放的40%,供热、其他行业和家庭燃烧分别占燃煤Cl~-排放的24%、22%和14%;钢铁行业为工业源的主要Cl~-排放源,约占工业源排放的90%,垃圾焚烧厂占全部Cl~-排放的61%,烹饪源中餐饮企业为最主要排放源,占烹饪源的70%;天然源海盐的排放量极少,未占到总排放的1%.从空间分布来看,浦东新区、宝山、普陀、松江和金山排放的HCl和Cl~-占到全市人为源总排放的80%,为主要的HCl和Cl~-排放区域.本文研究建立的上海地区大气中氯化氢和颗粒氯排放源清单,对于深入研究氯化学机制对二次污染的影响提供了重要的数据参考.     

基于稳定氢同位素的太原市大气单环芳烃来源

采集太原市城北和城南区域环境空气和5类污染源挥发性有机物样品,测定样品中典型单环芳烃稳定氢同位素（δD）组成,基于同位素质量平衡原理计算单环芳烃从源到环境空气受体的δD初始混合值,探讨单环芳烃来源.结果表明,柴油挥发源、溶剂挥发源、汽油挥发源（97^#）、汽油挥发源（95^#）、机动车尾气（97^#）、机动车尾气（95^#）和民用燃煤源中单环芳烃δD范围依次为：（-138.7‰~-115.5‰）、（-147.0‰~-121.0‰）、（-150.8‰~-117.6‰）、（-131.8‰~-113.8‰）、（-171.2‰~-120.0‰）、（-138.9‰~-102.7‰）和（-168.3‰~-142.3‰）,民用燃煤源中单环芳烃δD显著贫重氢同位素（D）组成,机动车尾气源与汽油挥发源中苯的δD相比显著贫D,可用于探索污染物转化过程;城北和城南环境空气中δD范围为（-131.7‰~-115.1‰）和（-131.9‰~-74.9‰）,δD初始混合值为-138.4‰和-173.9‰,体现了其来源差异.     

岩溶地下河污染物运移模型对比研究

两区模型（TRM）和暂时存储模型（TSM）为两种常用的岩溶地下河（管道）污染物运移模型,为了更好表征岩溶地下河污染物运移过程,开展模型对比研究.采用两种模型拟合室内管道示踪实验穿透曲线,从概念模型框架、模型优缺点、参数校正过程和物理意义、参数敏感性等方面对比分析两种模型的异同.结果表明,OTIS软件提供TSM的数值解,而CXTFIT软件提供TRM的解析解,但两者均能通过下游不同位置的穿透曲线分段表征地下河不同阶段的污染物运移过程.两种模型的物理意义相近,均可近似描述岩溶地下河中溶质的暂时性存储现象,较好地拟合溶质运移曲线.采用TSM可校正得到暂时存储区的横截面积,但采用TRM只能获得非流动区所占的比例.两种模型中弥散系数和传质/交换系数的敏感度较低,并且弥散系数的变化对穿透曲线拖尾无显著影响.研究结果为岩溶地下河污染物运移模型的选取与应用提供了依据.     

Photodegradation of Hexafluoropropylene Oxide Trimer Acid under UV Irradiation

As a novel alternative to traditional perfluoroalkyl substances (PFASs), including perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), hexafluoroproplyene oxide trimer acid (HFPO-TA) has been detected worldwide in surface water. Moreover, recent researches have demonstrated that HFPO-TA has stronger bioaccumulation potential and higher hepatotoxicity than PFOA. To treat these contaminants e.g. PFOA and PFOS, some photochemical techniques by adding exogenous substances had been reported. However, there is still no report for the behavior of HFPO-TA itself under direct UV irradiation. The current study investigated the photo-transformation of HFPO-TA under UV irradiation in aqueous solution. After 72 hr photoreaction, 75% degradation ratio and 25% defluorination ratio were achieved under ambient condition. Reducing active species, i.e., hydrated electrons and active hydrogen atoms, generated from water splitting played dominant roles in degradation of HFPO-TA, which was confirmed by different effects of reaction atmospheres and quenching experiments. A possible degradation pathway was proposed based on the products identification and theoretical calculations. In general, HFPO-TA would be transformed into shorter-chain PFASs, including hexafluoropropylene oxide dimer acid (HFPO-DA), perfluoropropionic acid (PFA) and trifluoroacetate (TFA). This research provides basic information for HFPO-TA photodegradation process and is essential to develop novel remediation techniques for HFPO-TA and other alternatives with similar structures.     

石期河流域地下水化学特征及物质来源分析

为明确典型岩溶溶丘洼(谷)地区域地下水化学特征及其成因,以石期河流域为研究对象,运用Gibbs图、Piper图、端元分析及离子比例系数等方法,对地下水水化学特征及物质来源进行了定性和定量分析.结果表明,研究区内地下水pH值介于6.06～8.07之间,Ca~(2+)、 Mg~(2+)和HCO~-_3是地下水中的主要离子,其质量浓度范围分别为2.61～108.7、 0.54～27.61和8.1～370.74mg·L~(-1),符合岩溶水高钙弱碱性特征;地下水物质成分中, Ca~(2+)和Mg~(2+)主要受到碳酸参与的灰岩和白云岩风化作用的控制, Na~+主要来源于硅酸盐岩的溶解,同时, Ca~(2+)和Na~+在地下水流动过程中进行阳离子交替吸附作用; K~+、 Cl~-和NO~-_3主要受到农业化肥施放和生活废水排放的影响.此外,大气降水作为该区域地下水的主要补给来源,对当地地下水化学特征和物质来源也有一定的影响.     

京津冀西北典型流域地下水化学特征及补给源分析

为揭示京津冀西北典型流域地下水循环特征,运用环境同位素和水化学技术等方法分析张家口市不同流域水体氢氧同位素特征、水化学特征及时空变化特征、地表地下水转化关系。结果表明：地表水化学类型主要为HCO₃-Mg·Na和HCO₃·Cl-Na型;地下水化学类型不同时期表现出不同的类型,水化学类型更为多样,主要以HCO₃-Mg·Na型、HCO₃·Cl-Na型、HCO₃·Cl-Na·Mg为主。地表河水和地下水中离子均主要来源于岩石风化作用;张北和桑干河流域地下水中离子偏向于蒸发浓缩作用控制。张家口市各流域地表地下水δ¹⁸O、δD组成较为接近,表明了当地地表水和地下水均受到大气降水的补给。大气降水和地表河水对地下水的补给比例均值分别为37.74%和62.26%,以地表河水的补给为主要方式。